- HOW TO RUN A WINDOWS 98 EMULATOR FOR FREE
- HOW TO RUN A WINDOWS 98 EMULATOR INSTALL
- HOW TO RUN A WINDOWS 98 EMULATOR PC
- HOW TO RUN A WINDOWS 98 EMULATOR WINDOWS
Setup the hard drive first, do a sys c:, then put the special disk in and reboot and it will do the rest of the work for you.ĭid you do the sys C: and did it boot from the hard drive?Įdited by Leurgy, 14 December 2014 - 09:05 PM.
HOW TO RUN A WINDOWS 98 EMULATOR INSTALL
In other words use the bootdisk you need that matches the OS you want to install ie win95/win98. Lets not go there though, its much more complicated than creating the boot disk and getting the cd-rom bootdisk.
HOW TO RUN A WINDOWS 98 EMULATOR PC
cab files to the hard drive, you would need to remove it from the laptop and put it in another pc as a slave drive and copy them there. You also need to create the autoexec.bat.Īs far as copying the. While Steam on Linux and rumored Linux support from Blizzard may change this in the future, games are the one category of app that have the most issues on Linux although many older games work perfectly.
HOW TO RUN A WINDOWS 98 EMULATOR WINDOWS
You would create a new one to replace the current one using the instructions above. You can’t run every Windows program on Linux when a big new PC game comes out, it will often be quite some time until it runs properly in Wine. They also have info on getting a cd-rom working in Dos.Īs far as opening the config.sys file, you don't need to. They've been around for years and have good reliable stuff. Use a boot diskette If your computer uses FAT16 or FAT32 and not NTFS create a boot disk and boot from that diskette to run the game.
HOW TO RUN A WINDOWS 98 EMULATOR FOR FREE
You can get a Win 98 boot disk for free from . If you are running Windows 95, 98, ME, or XP, change the compatibility of the program by right-clicking the shortcut, selecting Properties, and clicking the Compatibility tab. Make sure you keep the current ones.Īlso, what happened when you did Sys C:? If that worked, the laptop should have booted to a C:\> without the floppy.ĭon't like the look of that website at all. You would then copy the current ones off the floppy and replace them with the ones you made. You don't need to retype them, you can just copy and paste them into seperate notepad files and when you do that, go to File then Save as and in the box that opens change Save as type: to all files and then Save with the appropriate name. Its not just the Config.sys, but also Autoexec.bat that I suggested you try on the boot floppy. cab files to the hard drive and run setup from there.ĭid you try any of that? Its important you give me the info I'm looking for so that I can help. Not sure if your cd drive will become available then. If you boot from the floppy, assuming this hard drive is partitioned and formatted, you can run the command SYS C. These will only be hard drive letters, so the next available letter should be the cd drive.Ī little research shows that this was a common problem with that particular laptop. I think the pertinent command here is LH C:\MSCDEX /D:TOSCD001 /M:10. If you do edit those two files, you would of course leave out the number preceding each line.Ĭan you tell us where you got this boot disk? What does it contain? If it contains FDisk, from the A:\> prompt run FDisk /status to see how the drive letters are assigned. Perhaps if you edit the ones on the floppy to contain those commands it might work. Alternatively, click the minus sign button in the top left corner and then click the first button.This webpage from Toshiba describes the Config.sys and Autoexec.bat files you would need to run that laptop. Press Esc until you see the following screen and then press Enter. Here I have set the first floppy drive to 3.5" 1.44 MB in 86Box settings and configured the floppy drive A: to correspond.Īll that's left to do is save the settings. A: corresponds to the first floppy drive in 86Box settings, B: is the second one. There, choose a floppy drive icon to configure its type. Floppy configuration is under the Standard icon: Otherwise, just use arrow keys, Tab, Enter, and Esc to navigate the interface. If you configured mouse properly, you should be able to capture the mouse by clicking the VM screen, then you can use the mouse to click buttons in the GUI. That should land you at the following screen:
![how to run a windows 98 emulator how to run a windows 98 emulator](https://emulatorclub.com/wp-content/uploads/2020/06/SIXwindows98emulator.jpg)
You will probably want to spam the key straight from start, as the BIOS doesn't wait for long. When you see the above screen, press Del. According to your 86box.cfg, that should be an AMI BIOS.
![how to run a windows 98 emulator how to run a windows 98 emulator](https://dosbox-x.com/wiki/images/Windows:Windows_98_SETUP_03.png)
You are supposed to enter the BIOS setup of the VM, not your host computer.